TORONTO, June 17, 2021 - Xanadu Mines Ltd. (ASX: XAM, TSX: XAM) (Xanadu or the Company) is pleased to update the market on its on-going exploration program for porphyry copper and gold deposits at the Kharmagtai District in the South Gobi region of Mongolia.
Highlights
- Disciplined program continues to target and define higher grade zones at Kharmagtai.
- Partial Assays returned for drill holes KHDDH567 and KHDDH568, scissor holes following up KHDDH565 (see ASX/TSX Announcement dated 18 May 2021)
- KHDDH567 returns 86.7m @ 0.61% eCu from 660.3m
including 54m @ 0.75% eCu from 667m
including 6m @ 1.06% eCu from 669m
- KHDDH568 returns 46.4m @ 0.60% eCu from 693.7m
- This drilling confirms location of the broader zone of high-grade mineralisation but is interpreted to have missed the very high grade, gold-rich bornite zone due to displacement along the Fifty-Fifty fault. Current diamond drill hole KHDDH571 is a follow up to target this zone on the hanging wall side of that fault.
- Current 3 rig program includes two other diamond drill rigs focusing on resource expansion drilling at White Hill (KHDDH569) and Zaraa (KHDDH570). Visual results indicate:
- White Hill drill hole expands copper sulphide mineralisation by approximately 300m to the south of the current resource, indicates possible presence of higher-grade blocks.
- Zaraa drill hole expands interpreted mineralisation by approximately 100m to the east.
Xanadu's Chief Executive Officer, Dr Andrew Stewart, said "Xanadu is running a disciplined exploration program to define higher grade blocks within a large zone of >0.6% eCu mineralisation. Today's results show effective progress, which we expect to be a steady build over the next 6 months. Over this time, we will share both drill results and project implications on a regular basis.
The partial assay results from our scissor holes KHDDH567 and KHDDH568 demonstrate structural complexity in the high-grade Bornite Zone at Stockwork Hill, with the zone pinching and swelling along its interpreted strike length. Late structures have moved parts of the high-grade bornite zone, which is not uncommon in older systems such as Kharmagtai.
The estimated width of the defined high-grade mineralisation at the Stockwork Hill Deposit ranges between 20 and 100 metres, however this is limited by a lack of drill holes along the northern and southern flanks, which we will target through our drilling program.
For our resource growth objective, the visual mineralisation logged in current drill holes at White Hill and Zaraa are encouraging and highlight the potential for substantial expansion of the global resource.
We look forward to providing regular updates on this structured program as we build the grade and scale of Kharmagtai."
Partial Results for KHDDH567 and KHDDH568
KHDDH567 was drilled targeting the extensions of the high-grade bornite zone approximately 80m west. Assays for the 780m have been returned with results for the remaining 256m due within two weeks.
| Hole ID | From | Interval | Cu | Au | eCu |
| KHDDH567 | 660.3m | 86.7m | 0.36 | % | 0.49g/t | 0.61 | % |
| including | 667m | 54m | 0.42 | % | 0.66g/t | 0.75 | % |
| including | 669m | 6m | 0.56 | % | 0.98g/t | 1.06 | % |
KHDDH568 was drilled targeting the extensions of the high-grade bornite zone 80m. Complete assays have been returned KHDDH568.
| Hole ID | From | Interval | Cu | Au | eCu |
| KHDDH568 | 693.7m | 46.4m | 0.32 | % | 0.55g/t | 0.60 | % |
These holes show that the bornite zone appears to form in two compartments split by a fault (50:50 fault) Both drill holes intersected the bornite zone adjacent to the 50:50 fault and show that the bornite zone thins next to the fault.
Drilling is currently underway with KHDDH571 targeting the western compartment of the bornite zone where previous drill holes suggest the bornite zone thickens again (Figure 1). In plan view, the bornite zone appears to be offset by the 50:50 fault and the western compartment steps to the north (Figure 2).
Figure 1 is available at https://www.globenewswire.com/NewsRoom/AttachmentNg/15e82b79-fd58-4f17-8a88-e65165dd4bc5
Figure 2 is available at https://www.globenewswire.com/NewsRoom/AttachmentNg/ee7ae6fa-9762-4ba5-861f-0ad69adf2e28
Current Drilling
The Exploration Program is currently underway with three active diamond drill holes - KHDDH569, KHDDH570 and KHDDH571 (Figure 3).
Deeper extension of mineralisation under White Hill is being tested with drill hole KHDDH569. KHDDH569 is currently at 860m and based on visual estimates is in high-grade mineralisation (Figure 4). This is significant and should add a large volume of mineralisation to the White Hill deposit.
No significant high-grade mineralisation has been drilled at White Hill previously, and this current drilling suggests there the potential for blocks of higher-grade within the larger White Hill deposit (similar to those identified at Stockwork Hill).
At Zaraa, drill hole KHDDH570 is expanding the mineralisation there, pushing mineralisation over 100m to the east. KHDDH570 is currently at 850m and based on visual estimates has encountered over 500m of moderate grade mineralisation (Figure 5).
Current drill hole KHDDH571 aims to test the western extension of the gold-rich, bornite zone under Stockwork Hill (Figure 1). KHDDH571 is currently at 660m and approaching the zone of interpreted mineralisation.
Figure 3 is available at https://www.globenewswire.com/NewsRoom/AttachmentNg/c092c190-a568-4d1b-bf92-5ce59c0ad6bf
Figure 4 is available at https://www.globenewswire.com/NewsRoom/AttachmentNg/83b951b4-1cba-4307-a03e-d56602674cd4
Figure 5 is available at https://www.globenewswire.com/NewsRoom/AttachmentNg/38ebb766-515d-4887-b06b-a5379f94fb05
About Xanadu Mines
Xanadu is an ASX and TSX listed Exploration company operating in Mongolia. We give investors exposure to globally significant, large scale copper-gold discoveries and low-cost inventory growth. Xanadu maintains a portfolio of exploration projects and remains one of the few junior explorers on the ASX or TSX who control an emerging Tier 1 copper-gold deposit in our flagship Kharmagtai project. For information on Xanadu visit: www.xanadumines.com.
Andrew Stewart
CEO
Xanadu Mines Ltd.
Andrew.stewart@xanadumines.com
+61 409 819 922
This Announcement was authorised for release by Xanadu's Board of Directors.
Appendix 1: Drilling Results
Table 1: Drill hole collar
| Hole ID | Prospect | East | North | RL | Azimuth (?) | Inc (?) | Depth (m) |
| KHDDH567 | Stockwork Hill | 592605 | 4877304 | 1296 | 0 | -70 | 1,036.2 |
| KHDDH568 | Stockwork Hill | 592556 | 4877308 | 1295 | 0 | -70 | 1,104.6 |
| KHDDH569 | White Hill | 591766 | 4876609 | 1314 | 0 | -60 | 1,350 |
| KHDDH570 | Zaraa | 594727 | 4877204 | 1271 | 197 | -65 | 1,200 |
| KHDDH571 | Stockwork Hill | 592455 | 4877275 | 1295 | 0 | -65 | 1,000 |
Table 2: Significant drill results
| Hole ID | Prospect | From (m) | To (m) | Interval (m) | Au (g/t) | Cu (%) | CuEq (%) | AuEq (g/t) |
| KHDDH567 | Stockwork Hill | 263 | 322 | 59 | 0.07 | 0.14 | 0.17 | 0.34 |
| and | | 386 | 390 | 4 | 0.11 | 0.18 | 0.24 | 0.47 |
| and | | 436 | 440 | 4 | 0.07 | 0.18 | 0.21 | 0.42 |
| and | | 660.3 | 747 | 86.7 | 0.49 | 0.36 | 0.61 | 1.19 |
| including | | 660.3 | 743 | 82.7 | 0.51 | 0.37 | 0.63 | 1.23 |
| including | | 667 | 721 | 54 | 0.66 | 0.42 | 0.75 | 1.47 |
| including | | 669 | 675 | 6 | 0.98 | 0.56 | 1.06 | 2.07 |
| and | | 762 | 776 | 14 | 0.08 | 0.10 | 0.14 | 0.27 |
| assays pending |
| KHDDH568 | Stockwork Hill | 0 | 34 | 34 | 0.05 | 0.13 | 0.15 | 0.30 |
| and | | 286 | 441 | 155 | 0.06 | 0.15 | 0.18 | 0.35 |
| and | | 693.7 | 740.1 | 46.4 | 0.55 | 0.32 | 0.60 | 1.17 |
| including | | 696.2 | 740.1 | 43.9 | 0.56 | 0.33 | 0.61 | 1.20 |
| and | | 765.6 | 786 | 20.4 | 0.08 | 0.14 | 0.18 | 0.36 |
| and | | 798 | 834 | 36 | 0.10 | 0.11 | 0.16 | 0.32 |
| and | | 927 | 933 | 6 | 0.14 | 0.07 | 0.14 | 0.26 |
| and | | 955 | 963 | 8 | 0.18 | 0.01 | 0.10 | 0.20 |
| and | | 985 | 1,007 | 22 | 0.07 | 0.12 | 0.15 | 0.30 |
| including | | 1,001 | 1,005 | 4 | 0.06 | 0.37 | 0.40 | 0.79 |
| and | | 1,031 | 1,062 | 31 | 0.06 | 0.16 | 0.19 | 0.38 |
| including | | 1,055.7 | 1,060 | 4.3 | 0.16 | 0.53 | 0.61 | 1.20 |
Appendix 2: Statements and Disclaimers
Mineral Resources and Ore Reserves Reporting Requirements
The 2012 Edition of the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code 2012) sets out minimum standards, recommendations and guidelines for Public Reporting in Australasia of Exploration Results, Mineral Resources and Ore Reserves. The Information contained in this Announcement has been presented in accordance with the JORC Code 2012.
The information in this Announcement relates to the exploration results previously reported in ASX Announcements which are available on the Xanadu website at:
http://www.xanadumines.com/irm/content/announcements.aspx. The Company is not aware of any new, material information or data that is not included in those market announcements.
Competent Person Statement
The information in this announcement that relates to exploration results is based on information compiled by Dr Andrew Stewart, who is responsible for the exploration data, comments on exploration target sizes, QA/QC and geological interpretation and information. Dr Stewart, who is an employee of Xanadu and is a Member of the Australasian Institute of Geoscientists, has sufficient experience relevant to the style of mineralisation and type of deposit under consideration and to the activity he is undertaking to qualify as the "Competent Person" as defined in the 2012 Edition of the Australasian Code for Reporting Exploration Results, Mineral Resources and Ore Reserves and the National Instrument 43-101. Dr Stewart consents to the inclusion in the report of the matters based on this information in the form and context in which it appears.
Copper Equivalent Calculations
The copper equivalent (CuEq or eCu) calculation represents the total metal value for each metal, multiplied by the conversion factor, summed and expressed in equivalent copper percentage with a metallurgical recovery factor applied. The copper equivalent calculation used is based off the eCu calculation defined by CSA in the 2018 Mineral Resource Upgrade (see ASX Announcement dated 31 October 2018).
Copper equivalent (CuEq or eCu) grade values were calculated using the following formula:
eCu = Cu + Au * 0.62097 * 0.8235,
Where Cu = copper grade (%); Au = gold grade (gold per tonne (g/t)); 0.62097 = conversion factor (gold to copper); and 0.8235 = relative recovery of gold to copper (82.35%).
The copper equivalent formula was based on the following parameters (prices are in USD): Copper price = 3.1 $/lb (or 6,834 $ per tonne ($/t)); Gold price = 1,320 $ per ounce ($/oz); Copper recovery = 85%; Gold recovery = 70%; and Relative recovery of gold to copper = 70% / 85% = 82.35%.
Forward-Looking Statements
Certain statements contained in this Announcement, including information as to the future financial or operating performance of Xanadu and its projects may also include statements which are 'forward‐looking statements' that may include, amongst other things, statements regarding targets, estimates and assumptions in respect of mineral reserves and mineral resources and anticipated grades and recovery rates, production and prices, recovery costs and results, capital expenditures and are or may be based on assumptions and estimates related to future technical, economic, market, political, social and other conditions. These 'forward-looking statements' are necessarily based upon a number of estimates and assumptions that, while considered reasonable by Xanadu, are inherently subject to significant technical, business, economic, competitive, political and social uncertainties and contingencies and involve known and unknown risks and uncertainties that could cause actual events or results to differ materially from estimated or anticipated events or results reflected in such forward‐looking statements.
Xanadu disclaims any intent or obligation to update publicly or release any revisions to any forward‐looking statements, whether as a result of new information, future events, circumstances or results or otherwise after the date of this Announcement or to reflect the occurrence of unanticipated events, other than required by the Corporations Act 2001 (Cth) and the Listing Rules of the Australian Securities Exchange (ASX) and Toronto Stock Exchange (TSX). The words 'believe', 'expect', 'anticipate', 'indicate', 'contemplate', 'target', 'plan', 'intends', 'continue', 'budget', 'estimate', 'may', 'will', 'schedule' and similar expressions identify forward‐looking statements.
All 'forward‐looking statements' made in this Announcement are qualified by the foregoing cautionary statements. Investors are cautioned that 'forward‐looking statements' are not guarantee of future performance and accordingly investors are cautioned not to put undue reliance on 'forward‐looking statements' due to the inherent uncertainty therein.
For further information please visit the Xanadu Mines' Website at www.xanadumines.com.
Appendix 3: Kharmagtai Table 1 (JORC 2012)
Set out below is Section 1 and Section 2 of Table 1 under the JORC Code, 2012 Edition for the Kharmagtai project. Data provided by Xanadu. This Table 1 updates the JORC Table 1 disclosure dated 11 April 2019.
JORC TABLE 1 - SECTION 1 - SAMPLING TECHNIQUES AND DATA
(Criteria in this section apply to all succeeding sections).
| Criteria | JORC Code explanation | Commentary |
| Sampling techniques | - Nature and quality of sampling (e.g. cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc.). These examples should not be taken as limiting the broad meaning of sampling.
- Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used.
- Aspects of the determination of mineralisation that are Material to the Public Report.
- In cases where 'industry standard' work has been done this would be relatively simple (e.g. 'reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay'). In other cases, more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (e.g. submarine nodules) may warrant disclosure of detailed information.
| - Representative ? core samples were split from PQ, HQ & NQ diameter diamond drill core on site using rock saws, on a routine 2m sample interval that also honours lithological/intrusive contacts.
- The orientation of the cut line is controlled using the core orientation line ensuring uniformity of core splitting wherever the core has been successfully oriented.
- Sample intervals are defined and subsequently checked by geologists, and sample tags are attached (stapled) to the plastic core trays for every sample interval.
- Reverse Circulation (RC) chip samples are ? splits from one-meter (1m) intervals using a 75%:25% riffle splitter to obtain a 3kg sample
- RC samples are uniform 2m samples formed from the combination of two ? split 1m samples.
|
| Drilling techniques | - Drill type (e.g. core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc.) and details (e.g. core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc.).
| - The Mineral Resource estimation has been based upon diamond drilling of PQ, HQ and NQ diameters with both standard and triple tube core recovery configurations, RC drilling and surface trenching with channel sampling.
- All drill core drilled by Xanadu has been oriented using the "Reflex Ace" tool.
|
| Drill sample recovery | - Method of recording and assessing core and chip sample recoveries and results assessed.
- Measures taken to maximise sample recovery and ensure representative nature of the samples.
- Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.
| - Diamond drill core recoveries were assessed using the standard industry (best) practice which involves: removing the core from core trays; reassembling multiple core runs in a v-rail; measuring core lengths with a tape measure, assessing recovery against core block depth measurements and recording any measured core loss for each core run.
- Diamond core recoveries average 97% through mineralization.
- Overall, core quality is good, with minimal core loss. Where there is localized faulting and or fracturing core recoveries decrease, however, this is a very small percentage of the mineralized intersections.
- RC recoveries are measured using whole weight of each 1m intercept measured before splitting
- Analysis of recovery results vs grade shows no significant trends that might indicate sampling bias introduced by variable recovery in fault/fracture zones.
|
| Logging | - Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.
- Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc.) photography.
- The total length and percentage of the relevant intersections logged.
| - All drill core is geologically logged by well-trained geologists using a modified "Anaconda-style" logging system methodology. The Anaconda method of logging and mapping is specifically designed for porphyry Cu-Au mineral systems and is entirely appropriate to support Mineral Resource Estimation, mining and metallurgical studies.
- Logging of lithology, alteration and mineralogy is intrinsically qualitative in nature. However, the logging is subsequently supported by 4 Acid ICP-MS (48 element) geochemistry and SWIR spectral mineralogy (facilitating semi-quantitative/calculated mineralogical, lithological and alteration classification) which is integrated with the logging to improve cross section interpretation and 3D geological model development.
- Drill core is also systematically logged for both geotechnical features and geological structures. Where drill core has been successfully oriented, the orientation of structures and geotechnical features are also routinely measured.
- Both wet and dry core photos are taken after core has been logged and marked-up but before drill core has been cut.
|
| Sub-sampling techniques and sample preparation | - If core, whether cut or sawn and whether quarter, half or all core taken.
- If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry.
- For all sample types, the nature, quality and appropriateness of the sample preparation technique.
- Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples.
- Measures taken to ensure that the sampling is representative of the in situ material collected, including for instance results for field duplicate/second-half sampling.
- Whether sample sizes are appropriate to the grain size of the material being sampled.
| - All drill core samples are ? core splits from either PQ, HQ or NQ diameter cores. A routine 2m sample interval is used, but this is varied locally to honour lithological/intrusive contacts. The minimum allowed sample length is 30cm.
- Core is appropriately split (onsite) using diamond core saws with the cut line routinely located relative to the core orientation line (where present) to provide consistency of sample split selection.
- The diamond saws are regularly flushed with water to minimize potential contamination.
- A field duplicate ? core sample is collected every 30th sample to ensure the "representivity of the in-situ material collected". The performance of these field duplicates is routinely analysed as part of Xanadu's sample QC process.
- Routine sample preparation and analyses of DDH samples were carried out by ALS Mongolia LLC (ALS Mongolia), who operates an independent sample preparation and analytical laboratory in Ulaanbaatar.
- All samples were prepared to meet standard quality control procedures as follows: Crushed to 75% passing 2mm, split to 1kg, pulverised to 85% passing 200 mesh (75 microns) and split to 150g sample pulp.
- ALS Mongolia Geochemistry labs quality management system is certified to ISO 9001:2008.
- The sample support (sub-sample mass and comminution) is appropriate for the grainsize and Cu-Au distribution of the porphyry Cu-Au mineralization and associated host rocks.
|
| Quality of assay data and laboratory tests | - The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.
- For geophysical tools, spectrometers, handheld XRF instruments, etc., the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.
- Nature of quality control procedures adopted (e.g. standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision have been established.
| - All samples were routinely assayed by ALS Mongolia for gold
- Au is determined using a 25g fire assay fusion, cupelled to obtain a bead, and digested with Aqua Regia, followed by an atomic absorption spectroscopy (AAS) finish, with a lower detection (LDL) of 0.01 ppm.
- All samples were also submitted to ALS Mongolia for the 48-element package ME-ICP61 using a four-acid digest (considered to be an effective total digest for the elements relevant to the Mineral Resource Estimate (MRE)). Where copper is over-range (>1% Cu), it is analysed by a second analytical technique (Cu-OG62), which has a higher upper detection limit (UDL) of 5% copper.
- Quality assurance has been managed by insertion of appropriate Standards (1:30 samples - suitable Ore Research Pty Ltd certified standards), Blanks (1:30 samples), Duplicates (1:30 samples - ? core duplicate) by XAM.
- Assay results outside the optimal range for methods were re-analysed by appropriate methods.
- Ore Research Pty Ltd certified copper and gold standards have been implemented as a part of QC procedures, as well as coarse and pulp blanks, and certified matrix matched copper-gold standards.
- QC monitoring is an active and ongoing processes on batch by batch basis by which unacceptable results are re-assayed as soon as practicable.
- Prior to 2014: Cu, Ag, Pb, Zn, As and Mo were routinely determined using a three-acid-digestion of a 0.3g sub-sample followed by an AAS finish (AAS21R) at SGS Mongolia. Samples were digested with nitric, hydrochloric and perchloric acids to dryness before leaching with hydrochloric acid to dissolve soluble salts and made to 15ml volume with distilled water. The LDL for copper using this technique was 2ppm. Where copper was over-range (>1% Cu), it was analysed by a second analytical technique (AAS22S), which has a higher upper detection limit (UDL) of 5% copper. Gold analysis method was essentially unchanged.
|
| Verification of sampling and assaying | - The verification of significant intersections by either independent or alternative company personnel.
- The use of twinned holes.
- Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.
- Discuss any adjustment to assay data.
| - All assay data QAQC is checked prior to loading into XAM's Geobank data base.
- The data is managed by XAM geologists.
- The data base and geological interpretation is managed by XAM.
- Check assays are submitted to an umpire lab (SGS Mongolia) for duplicate analysis.
- No twinned drill holes exist.
- There have been no adjustments to any of the assay data.
|
| Location of data points | - Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.
- Specification of the grid system used.
- Quality and adequacy of topographic control.
| - Diamond drill holes have been surveyed with a differential global positioning system (DGPS) to within 10cm accuracy.
- The grid system used for the project is UTM WGS-84 Zone 48N
- Historically, Eastman Kodak and Flexit electronic multi-shot downhole survey tools have been used at Kharmagtai to collect down hole azimuth and inclination information for the majority of the diamond drill holes. Single shots were typically taken every 30m to 50m during the drilling process, and a multi-shot survey with readings every 3-5m are conducted at the completion of the drill hole. As these tools rely on the earth's magnetic field to measure azimuth, there is some localised interference/inaccuracy introduced by the presence of magnetite in some parts of the Kharmagtai mineral system. The extent of this interference cannot be quantified on a reading-by-reading basis.
- More recently (since September 2017), a north-seeking gyro has been employed by the drilling crews on site (rented and operated by the drilling contractor), providing accurate downhole orientation measurements unaffected by magnetic effects. Xanadu have a permanent calibration station setup for the gyro tool, which is routinely calibrated every 2 weeks (calibration records are maintained and were sighted)
- The project Digital Terrain Model (DTM) is based on 1m contours from satellite imagery with an accuracy of ?0.1 m.
|
| Data spacing and distribution | - Data spacing for reporting of Exploration Results.
- Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.
- Whether sample compositing has been applied.
| - Holes spacings range from <50m spacings within the core of mineralization to +500m spacings for exploration drilling. Hole spacings can be determined using the sections and drill plans provided.
- Holes range from vertical to an inclination of -60 degrees depending on the attitude of the target and the drilling method.
- The data spacing and distribution is sufficient to establish anomalism and targeting for porphyry Cu-Au, tourmaline breccia and epithermal target types.
- Holes have been drilled to a maximum of 1,300m vertical depth.
- The data spacing and distribution is sufficient to establish geological and grade continuity, and to support the Mineral Resource classification.
|
| Orientation of data in relation to geological structure | - Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type.
- If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.
| - Drilling is conducted in a predominantly regular grid to allow unbiased interpretation and targeting.
- Scissor drilling, as well as some vertical and oblique drilling, has been used in key mineralised zones to achieve unbiased sampling of interpreted structures and mineralised zones, and in particular to assist in constraining the geometry of the mineralised hydrothermal tourmaline-sulphide breccia domains.
|
| Sample security | - The measures taken to ensure sample security.
| - Samples are delivered from the drill rig to the core shed twice daily and are never left unattended at the rig.
- Samples are dispatched from site in locked boxes transported on XAM company vehicles to ALS lab in Ulaanbaatar.
- Sample shipment receipt is signed off at the Laboratory with additional email confirmation of receipt.
- Samples are then stored at the lab and returned to a locked storage site.
|
| Audits or reviews | - The results of any audits or reviews of sampling techniques and data.
| - Internal audits of sampling techniques and data management are undertaken on a regular basis, to ensure industry best practice is employed at all times.
- External reviews and audits have been conducted by the following groups:
- 2012: AMC Consultants Pty Ltd. was engaged to conduct an Independent Technical Report which reviewed drilling and sampling procedures. It was concluded that sampling and data record was to an appropriate standard.
- 2013: Mining Associates Ltd. was engaged to conduct an Independent Technical Report to review drilling, sampling techniques and QAQC. Methods were found to conform to international best practice.
- 2018: CSA Global reviewed the entire drilling, logging, sampling, sample shipping and laboratory processes during the competent persons site visit for the 2018 MRE and found the systems and adherence to protocols to be to an appropriate standard.
|
JORC TABLE 1 - SECTION 2 - REPORTING OF EXPLORATION RESULTS
(Criteria in this section apply to all succeeding sections).
| Criteria | Commentary |
Mineral
tenement
and land
tenure
status | - The Project comprises 2 Mining Licences (MV-17129A Oyut Ulaan and (MV-17387A Kharmagtai):
- Xanadu now owns 90% of Vantage LLC, the 100% owner of the Oyut Ulaan mining licence.
- The Kharmagtai mining license MV-17387A is 100% owned by Oyut Ulaan LLC. Xanadu has an 85% interest in Mongol Metals LLC, which has 90% interest in Oyut Ulaan LLC. The remaining 10% in Oyut Ulaan LLC is owned by Quincunx (BVI) Ltd ("Quincunx").
- The Mongolian Minerals Law (2006) and Mongolian Land Law (2002) govern exploration, mining and land use rights for the project.
|
Exploration
done by
other
parties | - Previous exploration at Kharmagtai was conducted by Quincunx Ltd, Ivanhoe Mines Ltd. and Turquoise Hill Resources Ltd. including extensive drilling, surface geochemistry, geophysics, mapping.
- Previous exploration at Red Mountain (Oyut Ulaan) was conducted by Ivanhoe Mines.
|
Geology
| - The mineralisation is characterised as porphyry copper-gold type.
- Porphyry copper-gold deposits are formed from magmatic hydrothermal fluids typically associated with felsic intrusive stocks that have deposited metals as sulphides both within the intrusive and the intruded host rocks. Quartz stockwork veining is typically associated with sulphides occurring both within the quartz veinlets and disseminated thought out the wall rock. Porphyry deposits are typically large tonnage deposits ranging from low to high grade and are generally mined by large scale open pit or underground bulk mining methods. The deposits at Kharmagtai are atypical in that they are associated with intermediate intrusions of diorite to quartz diorite composition; however the deposits are in terms of contained gold significant, and similar gold-rich porphyry deposits.
|
Drill hole
Information | - Diamond drill holes are the principal source of geological and grade data for the Project.
- See figures in this ASX/TSX Announcement.
|
Data
Aggregation methods | - The CSAMT data was converted into 2D line data using the Zonge CSAMT processing software and then converted into 3D space using a UBC inversion process. Inversion fit was acceptable, and error was generally low.
- A nominal cut-off of 0.1% eCu is used in copper dominant systems for identification of potentially significant intercepts for reporting purposes. Higher grade cut-offs are 0.3%, 0.6% and 1% eCu.
- A nominal cut-off of 0.1g/t eAu is used in gold dominant systems like Golden Eagle for identification of potentially significant intercepts for reporting purposes. Higher grade cut-offs are 0.3g/t, 0.6g/t and 1g/t eAu.
- Maximum contiguous dilution within each intercept is 9m for 0.1%, 0.3%, 0.6% and 1% eCu.
- Most of the reported intercepts are shown in sufficient detail, including maxima and subintervals, to allow the reader to make an assessment of the balance of high and low grades in the intercept.
- Informing samples have been composited to two metre lengths honouring the geological domains and adjusted where necessary to ensure that no residual sample lengths have been excluded (best fit).
The copper equivalent (eCu) calculation represents the total metal value for each metal, multiplied by the conversion factor, summed and expressed in equivalent copper percentage with a metallurgical recovery factor applied. The copper equivalent calculation used is based off the eCu calculation defined by CSA in the 2018 Mineral Resource Upgrade.
Copper equivalent (CuEq or eCu) grade values were calculated using the following formula:
eCu or CuEq = Cu + Au * 0.62097 * 0.8235,
Gold Equivalent (eAu) grade values were calculated using the following formula:
eAu = Au + Cu / 0.62097 * 0.8235.
Where:
Cu - copper grade (%)
Au - gold grade (g/t)
0.62097 - conversion factor (gold to copper)
0.8235 - relative recovery of gold to copper (82.35%)
The copper equivalent formula was based on the following parameters (prices are in USD): - Copper price - 3.1 $/lb (or 6834 $/t)
- Gold price - 1320 $/oz
- Copper recovery - 85%
- Gold recovery - 70%
- Relative recovery of gold to copper = 70% / 85% = 82.35%.
|
Relationship between mineralisation
on widths
and intercept
lengths | - Mineralised structures are variable in orientation, and therefore drill orientations have been adjusted from place to place in order to allow intersection angles as close as possible to true widths.
- Exploration results have been reported as an interval with 'from' and 'to' stated in tables of significant economic intercepts. Tables clearly indicate that true widths will generally be narrower than those reported.
|
| Diagrams | - See figures in the body of the report.
|
Balanced
reporting | - Resources have been reported at a range of cut-off grades, above a minimum suitable for open pit mining, and above a minimum suitable for underground mining.
|
Other
substantive
exploration
data | - Extensive work in this area has been done and is reported separately.
|
Further
Work | - The mineralisation is open at depth and along strike.
- Current estimates are restricted to those expected to be reasonable for open pit mining. Limited drilling below this depth (-300m RLl) shows widths and grades potentially suitable for underground extraction.
- Exploration on going.
|
JORC TABLE 1 - SECTION 3 - ESTIMATION AND REPORTING OF MINERAL RESOURCES
Mineral Resources are not reported so this is not applicable to this Announcement. Please refer to ASX Announcement dated 31 October 2018 for Xanadu's most recent reported Mineral Resource Estimate and applicable Table 1, Section 3.
JORC TABLE 1 - SECTION 4 - ESTIMATION AND REPORTING OF ORE RESERVES
Ore Reserves are not reported so this is not applicable to this Announcement.
